西藏燕麦主要种植区灌溉定额空间分布及影响因素

燕麦为西藏自治区典型牧草之一,由于种植区地域辽阔,灌溉试验结果受限,西藏燕麦主要种植区的灌溉定额尚不明确。本文在西藏燕麦主要种植区内选取28个典型站点进行资料收集,遵循农业气候相似原则进行区域划分,基于水量平衡法揭示了西藏燕麦主要种植区灌溉定额的空间分布特征,并根据统计学原理分析了其影响因素。研究表明:燕麦主要种植区的灌溉定额呈由西藏中部至东部呈现先递增后递减的趋势,50%水文年下的燕麦灌溉定额在56~265 mm之间变化。降雨量是影响研究区内燕麦灌溉定额的主要因素(R²为0.515),ET₀次之(R²为0.152);其它气象因素中,日照时数对研究区燕麦灌溉定额影响较大(R²为0.462),且呈正相关关系;相对湿度对燕麦灌溉定额影响较小。西藏燕麦主要种植区的灌溉定额及其空间分布可为西藏自治区灌溉用水管理提供支撑。     

楔横轧成形25CrMo4厚壁空心轴件的不圆度分析

机械结构轻量化的主要途径是在结构上采用空心轴.近年来, 采用楔横轧带芯棒轧制空心轴类件的工艺得到了较广泛的关注.厚壁空心轴类件在楔横轧轧制过程中易发生“失圆”现象.本文通过热压缩实验研究了25CrMo4合金钢在楔横轧变形条件下热变形行为, 获得其真应力-应变曲线.在此基础上, 基于Deform-3D有限元软件, 建立25CrMo4厚壁空心轴楔横轧有限元仿真模型, 分析厚壁空心轴楔横轧成形机理, 研究得出断面收缩率、成形角、展宽角对轧件不圆度的影响规律: 断面收缩率增大, 不圆度减小; 成形角增大不圆度减小, 轧制温度越高减小趋势越明显; 展宽角增大不圆度增大, 提高轧制温度抑制增大趋势.选取部分工艺参数进行楔横轧验证实验, 对比了有限元仿真结果和实验结果, 表明有限元仿真模型预测精度较高.      

Psychrophilic hydrogen production from petrochemical wastewater via anaerobic sequencing batch reactor: techno-economic assessment and kinetic modelling

Independent hydrogen production from petrochemical wastewater containing mono-ethylene glycol (MEG) via anaerobic sequencing batch reactor (ASBR) was extensively assessed under psychrophilic conditions (15–25 °C). A lab-scale ASBR was operated at pH of 5.50, and different organic loading rates (OLR) of 1.00, 1.67, 2.67, and 4.00 gCOD/L/d. The hydrogen yield (HY) progressed from 134.32 ± 10.79 to 189.09 ± 22.35 mL/gMEG_initial at increasing OLR from 1.00 to 4.00 gCOD/L/d. The maximum hydrogen content of 47.44 ± 3.60% was achieved at OLR of 4.0 gCOD/L/d, while methane content remained low (17.76 ± 1.27% at OLR of 1.0 gCOD/L/d). Kinetic studies using four different mathematical models were conducted to describe the ASBR performance. Furthermore, two batch-mode experiments were performed to optimize the nitrogen supplementation as a nutrient (C/N ratio), and assess the impact of salinity (as gNaCl/L) on hydrogen production. HY substantially dropped from 62.77 ± 4.09 to 6.02 ± 0.39 mL/gMEG_initial when C/N ratio was increased from 28.5 to 114.0. Besides, the results revealed that salinity up to 10.0 gNaCl/L has a relatively low inhibitory impact on hydrogen production. Eventually, the cost/benefit analysis showed that environmental and energy recovery revenues from ASBR were optimized at OLR of 4.0 gCOD/L/d (payback period of 7.13 yrs).     

La2O3对SiO2-CaO-Al2O3-MgO熔体黏度和结构的影响

使用分析纯物质模拟微晶玻璃熔体，分别采用柱体旋转法和拉曼光谱技术研究了La2O3含量对SiO2-CaO-Al2O3-MgO熔体黏度和结构的影响规律。结果表明：熔体黏度和黏流活化能随着La2O3含量的增加而降低；拉曼光谱表明La2O3能破坏硅酸盐结构（Qn），随着La2O3含量的增加，Q1、Q2的百分含量增加，Q3的百分含量减小，Q0的百分含量基本不变，表明熔体中非桥氧数量增加，熔体聚合度降低。La2O3在熔体中起网络修饰体的作用。     

全尾砂和废石联合胶结充填体最佳配比及应用

针对红岭铅锌矿分级充填骨料来源不足、地表废石堆积污染环境的情况,提出将该矿选厂产生的全尾砂和地表废石作为充填骨料的联合胶结充填方案。分别测试了全尾砂和地表废石的物理化学性质,验证了碎石和全尾砂作为联合充填骨料的可行性。通过充填配比试验,分析了不同配比全尾砂废石充填体强度特性,得出了最佳充填配比。结果表明,充填试块的强度随灰砂比减小而减小,随养护龄期增加呈增大趋势,随充填料浆质量浓度增大而增大,最佳配比为: 胶结充填灰砂比1∶8、普通充填灰砂比1∶12,全尾砂∶废石配比4∶6,质量浓度78%。根据研究结果,在红岭铅锌矿进行了全尾砂废石充填技术工业应用,证实该技术可行。     

水煤浆气化工艺水系统内优化处理探讨

通过分析水煤浆气化系统内各种水源的水质,提出将低压灰水作为气化系统内部的回用水源进行优化利用以减少一次水的使用量,通过设备改造、工艺操作优化等措施解决了系统内水循环利用后导致的悬浮物、COD、氨氮、总硬度等指标超标问题。     

Hydrothermal synthesis of 3D NixCo1−xS2 particles/graphene composite hydrogels for high performance supercapacitors

In this work, three dimensional (3D) Ni_xCo_1−xS₂/graphene composite hydrogels with different Ni contents (denoted as Ni_xCo_1−xS₂/GH (x = 0, 0.31, 0.56, 0.66, 1)) have been synthesized by a simple one-step hydrothermal method and utilized as the active materials of supercapacitors. The as-prepared samples present a 3D interconnected porous network with the pore sizes in the range of several to tens micrometers. Interestingly, the Ni_xCo_1−xS₂ particles are uniformly located on the graphene network and the particle size is evolved from ∼50 nm to ∼1.5 μm with the increase of Ni content. The electrochemical measurements revealed that the specific capacitance, rate capability and cyclability of different Ni_xCo_1−xS₂/GH electrodes are strongly affected by their different Ni content. Among these, the 3D Ni_0.31Co_0.69S₂/GH composite has the highest specific capacitance of 1166 F/g at a current density of 1 A/g. Furthermore, a specific capacitance of 559 F/g can be still maintained at high current density of 20 A/g. After 1000 charge–discharge cycles at 5 A/g, the specific capacitance remains a high value of 755 F/g.     

R-curves determination of ordinary refractory ceramics assisted by digital image correlation method

As a figure-of-merit, the rising ratio of crack propagation resistance to fracture initiation resistance indicates a reduction of the brittleness and enhances the thermal shock resistance of ordinary refractory ceramics. The significant nonlinear fracture behaviour is related to the development of a fracture process zone (FPZ). The universal dimensionless load–displacement diagram method is applied as a promising graphical method for the determination of R-curves for magnesia refractories showing different brittleness. By applying digital image correlation (DIC) together with the graphical method, the problems arisen with accurate determination of the fracture initiation resistance and the crack length are overcome. Meanwhile, the R-curve is subdivided with respect to the fracture processes, viz the fracture initiation, the development of FPZ and the onset of traction free macro-crack. With the simultaneous crack lengths evaluated from DIC, the contribution of each fracture process to the crack propagation resistance at certain loading stage is quantitatively presented.     

High erosion-oxidation performance of Fe-based Nb or V containing multi-component alloys with Co addition at 1173 K

High temperature erosion-oxidation behavior of Fe-based Nb or V containing multi-component alloys with Co addition is investigated at 1173 K. High temperature erosion tests and oxidation tests are conducted to determine both erosion and oxidation behaviors. Oxide scales are detected on the surfaces with 5V–10Nb and 5V–10Co showing superior erosion-oxidation resistance at 1173 K. The erosion rate is high in V-containing samples without Co due to the occurrence of vanadium oxide attack. Whilst, with increasing of Co content, the erosion rate is reduced, indicating the addition of Co is an effective counter-measure. In Nb-containing samples on the other hand, oxidation is successfully controlled by the formation of a composite oxide layer regardless of the presence of Co, thereby reducing the erosion losses.